Crab claw orchid longevity is cut with a knife and given with medicine, and it blooms one after anot

Last Update :2024.12.26

Article Catalog

Cut the longevity flower with a knife and add some medicine, and the buds will crowd the pot.

Cut the crab claw orchid with a knife and add some medicine, and it will bloom one after another.


Many flower lovers like to raise longevity flowers and crab claws. Although they are beautiful, after blooming once, it is difficult to bloom a second time that year, which is very unsatisfactory. However, if you prune it properly and add fertilizer and water, it will bloom 1~ Even 2 times is no problem!


Crab claw orchid longevity cut with 1 knife, feed tablets of medicine, bloom one crop after another, the basin is full!Cut the longevity flower with a knife and add some medicine, and the buds will crowd the pot.

Cut the longevity flower and feed some medicine, and the buds will crowd into the pot

"Cut it once"

1. Cut it before flowering

The longevity flower wants If it blooms more, it is necessary to top it more in the early stage of growth and cut off the top buds to promote branch growth. The more branches there are, the more flowers will bloom in the later period.

Crab Claw Orchid

Tips: When the seedlings are 10cm tall , keep 3~5 pairs of leaves and 5cm high stems, and then knock off the top buds

Crab Claw Orchid

This topping is accompanied by the entire growth process. The longevity flower will become more and more vigorous as it is cut until the buds emerge.

Crab Claw Orchid

2. Cut once after flowering

p>

After the flowers fade, quickly cut off the failed flower branches, and cut off the second pair of leaves along with the flower branches. After a period of time, new buds will grow and the flowers may bloom again.

Crab Claw Orchid

For old piles, you can wait until the flowers fade. Then cut it again. If you don’t cut it, the result will be very poor!

Crab Claw Orchid

Note: Be careful when cutting , the cutting position is above the axillary buds, so as to facilitate branching; retain a few large flowers and leaves to promote photosynthesis.

Crab Claw Orchid

"Feed some medicine"

Flowering consumes a lot of nutrients. After the flowers fade, the plant will be "weak". After pruning the flower branches that have faded, you should quickly add some granular fertilizer and bury a few grains of slow-release fertilizer along the edge of the pot to replenish the fertility and have the strength to bloom. Second crop of flowers.  

Crab Claw Orchid

Cut the Crab Claw Orchid and feed it Apply medicine and bloom one crop after another

"Cut one knife"

1. Cut one knife before flowering

During the budding period of crab claw orchid, the top of the branch It will grow many young leaves. These young leaves cannot bloom and will only consume nutrients. If you remove them, the flowers will bloom better.

Crab Claw Orchid

Note: If the If there are less than 4 leaves, don’t remove the young leaves at the top.

Crab Claw Orchid

2. Shave your head after flowering

p>

When the flowers droop and the branches feel a little soft, it means they are about to fail. At this time, cut off the flower branches and keep only 3 to 4 leaves on each branch, so that you can "recharge your batteries" in time. Prepare for the next bloom.

Crab Claw Orchid

"Feed some medicine"

1. After pruning, bury a circle of compound fertilizer on the edge of the flower pot, and water it after burying to make it strong as soon as possible;

2. After a month, spray some on the leaves Potassium dihydrogen phosphate solution and more sunshine at the same time. Soon, the second crop of flower buds will emerge!

Crab Claw Orchid


Cut the crab claw orchid with a knife and add some medicine, and it will bloom one after another.
















- END -

Methods and precautions for growing hydroponic tiger orchids

When cultivating tiger orchid in water, you should ensure that there is enough oxy...

How to propagate multi-head chrysanthemum and when to plant seeds

Chrysanthemums are commonly propagated by cuttings. The best time for cutting is b...